乐鱼·(中国)官方网站

贝特-智能仪表成套直供厂家12年制造经验 · 拥有核心知识产权

扫一扫加我微信扫一扫加我微信

供应订购热线:400-839-1983
13906214292

贝特新闻资讯

eh电磁流量计英文说明书-乐鱼官网

作者: 贝特设计师 编辑: 贝特小编 来源: 贝特智能乐鱼官网 发布日期: 2020.02.18
信息摘要:
l measurement is not affected by the variation of flow density, viscos…

summary

1.1features

l measurement is not affected by the variation of flow density, viscosity, temperature, pressure and conductivity. high accuracy measurement is guaranteed according to the linear measurement principle.

l no obstacle in the pipe, no pressure-loss and lower requirement for straight pipeline.

l dn 6 to dn2000 covers a wide range of pipe size. a variety of liners and electrodes are available to satisfy different flow characteristic.

l programmable low frequency square wave field excitation, improving measurement stability and reducing power consumption.

l implementing 16 bits mcu, providing high integration and accuracy; full-digital processing, high noise resistance and reliable measurement; flow measurement range up to 1500:1.

l high definition lcd display with backlight.

l rs485 or rs232 interface supports digital communication.

l intelligent empty pipe detection and electrodes resistance measurement diagnosing empty pipe and electrodes contamination accurately.

l smd component and surface mount technology (smt) are implemented to improve the reliability.

1.2main applications

electromagnetic flowmeter can be used to measure the volume flow of conductive fluid in a closed pipeline. it is widely applied in the flow measurement and control in the fields of chemical and petroleum industry, metallurgy industry, water and waste water, agriculture and irrigation, paper making, food and beverage industry and pharmaceutical industry.

1.3ambient conditions

ambient temperature: sensor: -25℃ to 60℃; converter: -25℃ to 60℃.

relative humidity: 5% to 90%;

1.4working conditions

maximum fluid temperature:

compact type: 60℃

remote type: teflon 150℃

neoprene 80℃; 120℃

polyurethane 70℃

fluid conductivity: ≥ 5ms/cm

1. working principles

2.1 measuring principles

the measuring principle of electromagnetic flowmeter is based on the electromagnetic induction law of farady. the sensor is mainly composed of measuring tube with isolate lining, a pair of electrodes installed by penetration of the measuring tube wall, a pair of coils and iron core to produce working magnetic field. when the conductive fluid flows through the measuring tube of the sensor, the voltage signal in direct proportion to the average flow velocity of the fluid will be inducted on the electrodes. the signal is amplified and treated by the transmitter to realize various display functions.

电磁流量计

2.2 converter circuit schematic

the converters supplies a stable exciting current to the coil in the sensor of electronetic flowmeters to get b constant and amplifies the electromotive force and convert it into standard signals of current or frequency so that the signals can be used for displaying, controlling and processing. the schematic of converter circuit is shown in fig. 2.1.

fig. 1 schematic of converter circuit

2. product classification

3.1product components

electromagnetic flowmeter is composed of sensor and converter. the remote-type also needs a special double-layer shielded cable to connect the converter and the sensor.

3.2product models

electromagnetic flowmeter has two forms: compact-type and remote-type. there are seven kinds of electrode materials and four kinds of lining materials available for sensor.

3. technical specification

4.1the flowmeter is compliant to standard “jb/t 9248-1999 electromagnetic flow meter”.

4.2maximum flow speed: 15m/s

4.3dn size: 3, 6, 10, 15, 20, 25, 32, 40, 50, 65, 80, 100, 150, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, 1800, 2000

4.4accuracy: 0.5%, 0.2%

4.5nominal pressure: 4.0mpa(dn0-150)

1.6mpa(dn200-600)

1.0mpa(dn700-1200)

0.6mpa(dn400-2000)

or other specified by order

4.6materials

electrode forms and materials:

electrode design has four forms: standard form, scraper form, detachable form and grounding electrode.

electrode material is selectable from stainless steel containing mo, stainless steel coated with carbonized tungsten, hastelloy b, hastelloy c, titanium, tantalum and platinum-iridium alloy.

flange material: carbon steel

grounding ring: stainless steel

inlet protection ring: carbon steel, stainless steel

4.7enclosure

ip65:

ip68: only available for remote-type sensor with neoprene or polyurethane liner, not including flameproof model.

4.8flameproof standard

dn15-dn600 compact-type: md ii bt4

dn15-dn1600 remote-type: sensor and converter both installed in dangerous area: md ii bt4.

dn15-dn1600 remote-type: sensor installed in dangerous area and converter installed in safe area: md ii bt4

4.9connection cable

special cable is needed to connect the sensor and the converter for remote-type flowmeter. the cable length should not exceed 100 meters. a 10-meter cable is supplied free of charge and the rest is to be ordered.

4.10general specification of converter

l power supply: ac 85-265v, 45-63hz, ≤20w; dc 11-40v

l converter display and operation: four keys are available to set all parameters. external handheld or pc can be used to do the configuration. high resolution lcd display with backlight, empty pipe detection and self-diagnostic function are equipped in the converter.

l digital communication: rs485, rs232, modbus,remote

l output signals:

- current output: fully-isolated, 4-20ma/0-10ma

load resistance: 0-10ma: 0-1.5kω; 4-20ma: 0-750ω.

- frequency output: bidirectional flow output. frequency output is proportional to the flow percentage of the full range. the converter provides fully isolated transistor open collector frequency output ranged from 1 to 5000 hz. the external dc power supply should not exceed 35v and maximum collector current is 250ma.

- pulse output: bidirectional flow output. the converter can output up to 5000cp/s pulse series, which is dedicated to external totalization. pulse factor is defined as volume or mass per pulse. it can be set to 0.001l/p, 0.01l/p, 0.1l/p, 1l/p, 2l/p, 5l/p, 10l/p, 100l/p, 1m3/p, 10 m3/p, 100 m3/p or 1000 m3/p. pulse width is selectable from auto, 10ms, 20ms, 50ms, 100ms, 150ms, 200ms, 250ms, 300ms, 350ms and 400ms. photo-coupler isolated transistor open collector circuit is used for pulse output. the external dc power supply should not exceed 35v and maximum collector current is 250ma.

- flow direction indication: the converter is capable of measuring both forward and reverse flow and recognizing its direction. the converter outputs 0v low level for forward flow, while 12v high level for reverse flow.

- alarm output: two channels of photo-coupler isolated open collector circuit are used for alarm signal output. there are two alarm outputs: high limit alarm and low limit alarm. the external dc power supply should not exceed 35v and maximum collector current is 250ma.

- damping constant: damping time is selectable from 0.2 to 100s.

详细的电磁流量计英文说明书请点击下载。电磁流量计英文版说明书.doc

本文由于"苏州贝特智能仪表原创”https://www.beitemeter.com/articles/dclljj.html

product recommendation产品推荐
  • 本安型水平安装金属转子流量计本安型水平安装金属转子流量计
  • 报警型金属转子流量计 报警型金属转子流量计
  • 远传金属转子流量计远传金属转子流量计
  • 防爆型金属管转子流量计 防爆型金属管转子流量计
  • 防腐型金属管转子流量计 防腐型金属管转子流量计
  • 不锈钢金属管浮子流量计 不锈钢金属管浮子流量计
贝特推荐资讯
如何设置电磁流量计的参数?

如何设置电磁流量计的参数?

何设置电磁流量计的参数?通常需要设置电磁流量计的参数,但很多人不知道如何设置电磁流量计的参数。现在让我们简要介绍一下如何设置电磁流量计的参数。一般参数设置在一定范围内,不同厂家有一定差异,以产品说明书为准,电磁流量计传感器实时测量流体电阻值。管道是否处于全管状态,因此空管测量值为连续值。虽然不同的流体有不同的电阻值来确定流量计管道是否处于全管状态,但它是空管测量值的连续值。虽然不同的流体有不同的电阻值,但只要流体处于满管状态,其电阻值就是稳定的
金属转子流量计的使用范围

金属转子流量计的使用范围

金属转子流量计一般根据锥形管材料的不同,可分为玻璃转子流量计和金属管转子流量计两类。前者一般为本地指示型,后者一般为流量变送器。金属管转子流量计可分为气体传输、电气传输、指示、报警、带积算等。根据变送器的结构和用途,可分为夹套绝缘、耐腐蚀、高压、高温等。
污水的换算单位

污水的换算单位

污水处理中的一些计算并不是非常复杂和相对简单,但是烦人的是单位的转换和十六进制的变化。在介绍水处理计算之前,我们首先对污水处理中的单元进行介绍。在未来的计算中,需要对使用单位进行大量的转换,因此非常有必要彻底了解水处理中的单位

咨询热线

400-839-1983
网站地图